Own crews · Own trailers · NJ
Industrial Electrical Equipment Buyer for Ramtown, NJ Facilities
Most Ramtown plant engineers call us at one of two moments: the week a capital upgrade is approved, or the week a demolition contractor asks who is taking the electrical scope. The question is the same either way — what is it worth, and who gets it out of the building? One written offer answers both, because we are the buyer, the removal contractor and the hauler.
New Jersey · statewide- Location
- Ramtown, NJ
- State
- New Jersey
- Utilities
- PSE&G, JCP&L, Atlantic City Elec
- Offer
- Same business day
- Payment
- Before load-out
- Phone
- 954-740-1983
Plate 01
Buying electrical equipment in Ramtown
Our New Jersey routing runs along I-95, the Turnpike, I-287, I-78 and I-80, which keeps trailer and crew cost predictable on Ramtown projects. Utility territory matters too — PSE&G, JCP&L, Atlantic City Electric each have their own clearance, metering and disconnect expectations, and we have worked inside them. Chemical and pharmaceutical plants along the Turnpike corridor plus dense urban building renovations make New Jersey one of our highest-volume states for switchboards, busway risers and MV switchgear.
If the Ramtown equipment is still carrying load, we phase it. Usually that means dead sections and spares first, then distribution as circuits are released, then the main line-up once the last feeder is isolated. The phasing goes into the offer so nobody is improvising in an energized room at two in the morning.
Plate 02
What we buy in Ramtown
Fourteen categories. We buy every one of them at Ramtown sites.
Electrical Switchgear
Low and medium voltage, indoor and outdoor
480 V – 38 kV, up to 5,000 AGenerators
Standby, prime and mobile sets
100 kW – 3 MW diesel and gasTransformers
Pad-mount, dry-type, substation, unit
75 kVA – 50 MVABus Plugs
Fusible switch and circuit-breaker plugs
30 A – 1,200 A fusible and breakerBus Duct & Busway
Feeder and plug-in, copper and aluminum
225 A – 5,000 A runsPanelboards & Switchboards
Panelboards, switchboards, distribution
100 A – 4,000 AWire & Cable
Copper and aluminum, new and reclaimed
#12 AWG – 1,000 MCMLoad Banks
Resistive and reactive, portable and permanent
100 kW – 3 MW resistiveCircuit Breakers
Molded case, insulated case, air, vacuum
15 A – 6,000 A framesMotor Control Centers
Low and medium voltage MCCs
MCC line-ups, buckets, VFD sectionsSubstations
Up to 138 kV primary
Complete unit and station substationsTransfer Switches
Automatic, manual, bypass-isolation
100 A – 4,000 A ATSCapacitors & Power Quality
Fixed and automatic capacitor banks
50 kVAR – 10 MVARComplete Plant Lots
One deal, one crew, one number
Whole-facility electrical scopePlate 03
What drives the number
Transformer oil is the item sellers in Ramtown worry about most, and fairly so. We test it, drain it, manifest it through licensed handlers and hand you the documentation. PCB-suspect units are handled under their own waste profile. The cost of that handling is already inside the offer, so nothing surprises you after the fact.
| Input | Detail |
|---|---|
| Condition | Working, retired, water-damaged, or already dismantled |
| Support | Are breakers and parts still available for this line-up? |
| Copper | Windings, bus bar and cable weight |
| Access | Rigging path, crane need, dock reality at the Ramtown site |
| Freight | I-95, the Turnpike, I-287, I-78 and I-80 |
Plate 04
Safety and documentation
Safety is scope, not a brochure page. Crews working in Ramtown operate to NFPA 70E for arc-flash boundaries and PPE, follow OSHA 1910.147 lockout and tagout with our own locks and written procedures, and hold a daily job safety analysis before the first bolt turns. We do not energize, test or operate your equipment — isolation is verified with your electrician before we touch anything.
Paper you receive
Certificate of insurance before we mobilize, a written itemized offer, a signed bill of sale, and load documentation for every trailer. If your compliance team needs something specific, ask before we schedule.
Plate 05
Nearby cities and buyer desks
Other New Jersey locations we buy electrical equipment in:
Plate 06
Ramtown questions
What happens to the equipment after you buy it?
Serviceable gear is tested, reconditioned where needed and resold as replacement equipment — that resale is what funds your offer. What cannot go back into service is dismantled for copper, aluminum and steel recovery through permitted processors, with regulated fractions documented.
Do you buy equipment that is still energized and in service?
Yes, and most of what we buy is. We quote it now and remove it on your cutover date. Telling us at the quote stage which Ramtown assets are still live lets us build the phasing and the clearance coordination into the schedule from the beginning.
Our electrical room is in a basement with a tight door. Is that a problem?
It is routine. Switchgear sections, transformers and gensets frequently have to be cut down or partially disassembled to clear a door width, an elevator limit or a stair turn. The access survey at your Ramtown site establishes the path before we commit to a date, and that cost is already inside the offer.
Will you take the equipment we cannot sell along with the good items?
Yes, and this is usually why sellers choose us. Cherry-picking leaves you holding the leftovers of the leftovers. We price the Ramtown lot as a whole — good gear, obsolete gear and the scrap fraction together — so the electrical room ends up genuinely empty.
Do you provide documentation for surplus property or audit records?
Yes. Itemized purchase agreements, weight tickets, bills of lading, oil disposal manifests and recycling documentation are standard on Ramtown purchases. Public agencies and audited facilities get the paperwork their process requires without having to ask twice.
Do you actually buy electrical equipment in Ramtown, or just broker it?
We buy it. Industrial Electrical Buyer is the purchaser of record — we fund the purchase, send our own crews to Ramtown to disconnect and load, and take title when the equipment leaves your dock. There is no third party behind us waiting to approve the price.
Form 1 — Request for Offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call or text 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
Electrical equipment in Ramtown?
Photos of the nameplates are enough to start. Written offer the same business day.